Here's the kit you've been waiting for to upgrade your Rowe BC series bill changer machine.

SIMPLE

You will replace all of Rowe’s electronics with 1 straightforward control box and free-standing Mars bill acceptor. NO MORE bucket problems. Gone are worn magnetic heads and high transport repair costs. No MORE trying to figure out which part is the cause of the problem.

RELIABLE

This kit uses Mars 'state-of-the-industry' acceptor: highest security, minimal maintenance. All of the electronic controls contained in one small control box; along with non-resetable counters for 'dollars in' and 'each coin hopper'.

SECURE

Your new, heavy stainless steel bracket will provide the smallest possible bill acceptor opening exposure to users/ vandals,  This minimizes possible vandal damage. The MEI acceptor has Industry-leading security against 'stringing'.

Rowe Bill Changer Parts
Rowe Bill Changer Parts

The above pictures show the greatly increased vandal security offered by the “Genesis kit” on the right vs. the standard BA50 opening. The exposed opening of the “Genesis kit” is only 13/16″ x 2 15/16″ compared to 2 5/8″ x 3 3/16″ for the BA50.

Some other kits use a bill acceptor with the bill opening pointing upward.  THIS IS NOT GOOD. Rain can easily get into acceptor. Small trash will fall into acceptor, and kids will drop stuff in (cause they're kids). We use the proper nose-piece; which angles downward slightly, to keep most unwanted "stuff" out of the bill acceptor.

Replace either of these existing Rowe parts setups- BA50 or BA35

Rowe Bill Changer Upgrade Kit
Rowe Bill Changer Upgrade Kit

with the simpler “Genesis kit”– (original bracket shown here)

Rowe Bill Changer Upgrade Kit

Here is the “new style brackets” we’re using-

Rowe Bill Changer Bracket
Rowe Bill Changer Bracket
Rowe Bill Changer Bracket
Rowe Bill Changer Bracket

Here is the complete installation in a BC200 machine, others are similar.

Rowe BC200 Upgraded Parts
Rowe Bill Changers; parts upgrade

“Genesis kits” available now for rear-load Rowe models: BC2RC, BC200, BC12R, BC1400, BC2800

“Genesis kits” also available for front-load Rowe models: BC11, BC115, BC12, BC20, BC25, BC35, BC1200, BC3500

Complete “Genesis kit” for Rowe: including control box, Mars AE2681 bill acceptor, and acceptor mounting bracket is only $1095.00

“Genesis” controller and harnessing only -
If you have already installed a Mars acceptor into your Rowe machine with some other kit and connected it into the existing Rowe control system; the “Genesis” controller and harness will connect to your existing Mars AE2600 series, and allow you to remove the remaining Rowe pieces and simulate the full “Genesis kit”.  The controller/harness is only $499.00 and uses your existing Mars acceptor and bracket. Great way to finish off improving your machine reliability. (other vending validator conversions may also be compatible)  Add $15 if you are using existing AE2400 or VN2500 series; as they require special harnesses.

  • Uses the popular Rowe Mars AE2600 bill acceptor. High security against ‘stringing’ and minimal maintenance. High capacity "1000" bill box.  Accepts bills all 4-ways if you wish.  Usually we use 2-way acceptance (green side up).
  • Mars bill acceptor is “self contained”. If it’s rejecting bills (in and out); the problem is in the Mars- no “ifs, ands, or buts” .
  • High security stainless steel mounting bracket- minimum possible opening size (13/16″ x 2 15/16″) to keep vandal damage to minimum.
  • Eliminate all of the confusing Rowe assemblies: CCC, power supply, dispenser bucket assemblies, bill transport and stacker.
  • Eliminate “bucket errors”.
  • Now pays out in ‘real time’; straight from the coin hoppers to customer.
  • Eliminate expensive BA50 repairs due to worn mag. head assemblies and erratic sensors.
  • Retains Rowe’s durable coin hoppers.
  • One simple new control box. Three "simple to understand" indicator lights.
  • Can replace BA50 systems, or earlier BA35 systems and gain up to $20 acceptance in any model machine.
  • If bill acceptor gets ‘jammed’, machine out of order light will come on.
  • Non-resetable counters for “dollars in” and each coin hopper.
  • Some kits can be modified for a coin acceptor to take in coins.
  • Genesis control is pre-programmed with payout schedule. Default payout is for all coin hoppers to be 25c. Alternate plan is for all hoppers to be $1 value. Other payout schedules can be programmed- many are already available.
  • Genesis controller can replace the old, worn-out Rowe electrical components in machines that have already had a Mars acceptor (and maybe others) installed from a previous conversion.